Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-1 8.1974 and later
Type-4 8.1972 and later
CT/CZ
Waterboxer engines until 7.1985 (1900cc DF all years)
The parts mentioned here have a close relationship with the selected part and are often ordered along with the selected part or searched for.
Tip: if you do not get a good search result when entering a keyword try a part that has something to do with it, if there is a related tab, the searched item is often mentioned there.
Foam air cleaner element
Height: 50 mm
Diameter: 135 mm
Fits air cleaner: #2148, #2152 and #5121 Paruzzi number : 2147
If the selected part does not apply to your Volkswagen type, check this list of the same parts that fit on other construction years or other types of cars.
Air filter
Type-1 engine 1200cc 8.1975 and later, 1300/1600cc 8.1971 and later Paruzzi number : 2149 Original VW number : 113129620
Useful information from Paruzzi magazine and from our YouTube channel :
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine overhaul - video 20 pushrod tubes With the cylinder heads out of the way, you can install standard pushrod tubes. But, disassembling the cylinder heads means replacing the gasket between cylinders and crankcase.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
fuel circuit - concept The combustion engine of our air-cooled Volkswagen uses a mixture of petrol and air. It is extremely important that both the amount of air and the purity of the air are regulated, this also applies to the petrol. Unfortunately, the petrol circuit is not very well known to enthusiasts and it is not always well maintained.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.