Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-1 engines 1600 AS, AF 1975 (VIN 216 2118 506) and later
Type-4 engines 1800 AW, AP 1974 (VIN 214 2125 001) until 7.1974
CT/CZ engines
Waterboxer engines 1900 until 1983 (DF until 027930, DG until 017790, DH until 002 308)
The parts mentioned here have a close relationship with the selected part and are often ordered along with the selected part or searched for.
Tip: if you do not get a good search result when entering a keyword try a part that has something to do with it, if there is a related tab, the searched item is often mentioned there.
Brake and clutch cleaner
Content: 500 ml Paruzzi number : 50150
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.